msgbartop
Blog di Dino Ciuffetti (Bernardino in realtà)
msgbarbottom

28 Nov 15 How to enable HTML5 video playback in firefox

If you use Mozilla Firefox and you want to view video streaming with HTML5 embedded players, you may need to enable some video functionality into the firefox configuration.
For some reason obscure to me Mozilla Firefox will not play some HTML5 based video streaming, and the embedded player will probably fall back to Adobe Flash based streaming (that is what I don’t want since it’s closed source and it’s a very insecure application).

For example, youtube has a HTML5 based player that you could choose to use instead of flv. You can verify and enable HTML5 based streaming functionality of your browser navigating to https://www.youtube.com/html5.

In my case (Firefox 64 bit on Linux Debian) the tabs “Media Source Extensions”, “MSE & H.264” and “MSE & WebM VP9” are disabled by default.

If you want to enable those functionalities simply write “about:config” into the firefox navigation bar.
You will be alerted to pay attention to not modify things or your warranty will be broken.
Just ignore the warning and proceed.

Now, if you did not already, switch the following configuration parameters to true:

media.fragmented-mp4.exposed
media.fragmented-mp4.ffmpeg.enabled
media.fragmented-mp4.gmp.enabled
media.mediasource.webm.enabled
media.mediasource.enabled

If you try to refresh the HTML5 based youtube player, you should hopefully have all video streaming tabs ready and enabled.
If you want, you can now switch the youtube default player to HTML5.

02 Apr 14 Adafruit 4-Digit 7-Segment Display Backpack on raspberry pi in C

In my previous blog post I published a TSL2561 light sensor driver in C for Raspberry PI. In this article I will publish a user space C driver for Adafruit 4-digit 7-segment display.

This is based on a HT16K33 led driver IC, that it’s a I2C driven RAM mapping 16*8 LED controller driver.

The driver I’m posting it’s valid for the adafruit circuit only, since it’s completely based on the electronic schematic they realized.
Don’t use the driver with other circuits, since the display could not function properly.
Basically the adafruit 7-segment backpack (http://www.adafruit.com/products/879) uses 8 (rows) * 5 (columns) HT16K33 lines to drive its leds. The column number 1 is dedicated to the first digit, the second column is dedicated to the second digit, the third column is attached to the colon sign in the middle of the 4 digits, the fourth column is attached to the third digit, and the fifth colum to the fourth display digit.

adafruit_7seg_schematic

While each row drives a single led of the given column.

The display columns 0, 1, 3, 4 can show numbers and some letters (A-F, n, o, i, l, L, etc…) plus a decimal point, while the column 2 can only show a colon sign (:).
A number or a letter for each digit is composed by 7 led segments, so the possibilities are few… but not so few after all (check 7seg.txt file attachment for more details on letter composition).

So, now comes the fun. How can I access the led driver memory to light display digits in C? Adafruit releases proof of concept libraries in C and python, but they don’t seem to run on my raspberry pi.
Since I am too lazy to port their code with external dependencies, I decided to write my own library in C.

#include "7seg_bp_ada.h"

/* prepare the backpack driver
(the first parameter is the raspberry pi i2c master controller attached to the HT16K33, the second is the i2c selection jumper)
The i2c selection address can be one of HT16K33_ADDR_01 to HT16K33_ADDR_08
*/
HT16K33 led_backpack1 = HT16K33_INIT(1, HT16K33_ADDR_01);

/* initialize the backpack */
rc = HT16K33_OPEN(&led_backpack1);

/* power on the ht16k33 */
HT16K33_ON(&led_backpack1);

/* make it shining bright */
HT16K33_BRIGHTNESS(&led_backpack1, 0x0F);

/* make it not blinking */
HT16K33_BLINK(&led_backpack1, HT16K33_BLINK_OFF);

/* power on the display */
HT16K33_DISPLAY(&led_backpack1, HT16K33_DISPLAY_ON);

/* Say hello */
HT16K33_UPDATE_DIGIT(&led_backpack1, 0, 'H', 0); // first digit
HT16K33_UPDATE_DIGIT(&led_backpack1, 1, 'E', 0); // second digit
// turn off the colon sign in the middle of the 4 digits
HT16K33_UPDATE_DIGIT(&led_backpack1, 2, HT16K33_COLON_OFF, 0);
HT16K33_UPDATE_DIGIT(&led_backpack1, 3, '#', 0); // third digit
HT16K33_UPDATE_DIGIT(&led_backpack1, 4, 'o', 0); // fourth digit
HT16K33_COMMIT(&led_backpack1); // commit to the display memory

// call this if you want to shut down the device (power saving mode)
// HT16K33_OFF(&led_backpack1);

/* close things (the display remains in the conditions left) */
HT16K33_CLOSE(&led_backpack1);

I decided to release the software with the liberal apache 2 license, so feel free to use this software inside your commercial, non free software / firmware.

Below you will find the files .c and .h that you can embed into your project.
It’s helpful for me, and I hope it will be helpful for you.

Ciao, Dino.

Note: on Raspberry PI OS (and debian) you need libi2c-dev (apt install libi2c-dev) before compiling.

gcc -Wall -O2 -o 7seg_bp_ada.o -c 7seg_bp_ada.c
gcc -Wall -O2 -o 7seg_bp_ada_test.o -c 7seg_bp_ada_test.c
gcc -Wall -O2 -o 7seg_bp_ada_test 7seg_bp_ada.o -li2c 7seg_bp_ada_test.o

7seg_bp_ada.c
7seg_bp_ada.h
7seg_bp_ada_test.c

19 Mar 14 TSL2561 light sensor on Raspberry pi in C

After I bought a new TSL2561 digital light sensor from Adafruit, I found that the very cool and small device cannot be accessed directly from linux (rasbian doesn’t have it’s kernel module compiled). Since I didn’t want to cross recompile my whole raspberry pi kernel just to have the tsl2563.ko driver enabled, and since it seems that raspbian does not relase genuine kernel headers to just compile custom kernel modules, I decided to write a user space simple library driver in C.

I found out that Adafruit relases proof of concept libraries written in C++ and python to access its hardware devices, the problem is that the c++ version is ready for arduino but it was not so directly usable for my raspberry pi. It also makes use of an adafruit unified sensor library and other external stuff. Since I am too lazy I decided yesterday to write a new simple library in plain C without external dependencies, just ready for my raspberry pi.

This is the arduino version that inspired me: https://github.com/adafruit/TSL2561-Arduino-Library
This is another cool blog post that inspired me (it now seems dead!!): http://russelldavis.org/2013/03/23/raspberryhunt-part-2/

This is an example:

/* prepare the sensor
(the first parameter is the raspberry pi i2c master controller attached to the TSL2561, the second is the i2c selection jumper)
The i2c selection address can be one of: TSL2561_ADDR_LOW, TSL2561_ADDR_FLOAT or TSL2561_ADDR_HIGH
*/
TSL2561 light1 = TSL2561_INIT(1, TSL2561_ADDR_FLOAT);

/* initialize the sensor */
rc = TSL2561_OPEN(&light1);

/* sense the luminosity from the sensor (lux is the luminosity taken in "lux" measure units)
the last parameter can be 1 to enable library auto gain, or 0 to disable it */
rc = TSL2561_SENSELIGHT(&light1, &broadband, &ir, &lux, 1);

TSL2561_CLOSE(&light1);

Compile:

gcc -Wall -O2 -o TSL2561.o -c TSL2561.c
gcc -Wall -O2 -o TSL2561_test.o -c TSL2561_test.c
gcc -Wall -O2 -o TSL2561_test TSL2561.o TSL2561_test.o

The output is like this:

root@rasponi:~/test/gpio# ./TSL2561_test
Test. RC: 0(Success), broadband: 141, ir: 34, lux: 12

As you can see it’s very easy at this point to get the light measures in C. Just include TSL2561.c and TSL2561.h inside your project and use the public APIs to setup and sense the IC.

I decided to release the code with the liberal apache v2 license, so feel free to include it into your commercial projects if you like.

It’s useful for me, and I hope that it can be useful to you too. Obviously it comes with absolutely no warranty.

p.s.1: I left the hardware stuff out of this article (just attach +vcc, gnd and i2c bus to the sensor
p.s.2: you have to load two kernel modules to get i2c bus working on you Raspberry pi:

modprobe i2c_bcm2708
modprobe i2c_dev

Ciao, Dino.

TSL2561.c
TSL2561.h
TSL2561_test.c

This is an example on how to use all 3 sensors on the same i2c bus:

#include <stdio.h>
#include <string.h>
#include "TSL2561.h"

int main() {
	int i;
	int rc;
	uint16_t broadband, ir;
	uint32_t lux=0;
	TSL2561 lights[3]; // we can handle 3 sensors
	
	// prepare the sensors
	// (the first parameter is the raspberry pi i2c master controller attached to the TSL2561, the second is the i2c selection jumper)
	// The i2c selection address can be one of: TSL2561_ADDR_LOW, TSL2561_ADDR_FLOAT or TSL2561_ADDR_HIGH
	
	// prepare all sensors
	/* cannot assign that way
	lights[0] = TSL2561_INIT(1, TSL2561_ADDR_LOW);
	lights[1] = TSL2561_INIT(1, TSL2561_ADDR_FLOAT);
	lights[2] = TSL2561_INIT(1, TSL2561_ADDR_HIGH);
	*/
	
	// initialize at runtime instead
	// FIRST SENSOR --> TSL2561_ADDR_LOW
	lights[0].adapter_nr=1;						// change this according to your i2c bus
	lights[0].sensor_addr=TSL2561_ADDR_LOW;				// don't change this
	lights[0].integration_time=TSL2561_INTEGRATIONTIME_402MS;	// don't change this
	lights[0].gain=TSL2561_GAIN_16X;				// don't change this
	lights[0].adapter_fd=-1;					// don't change this
	lights[0].lasterr=0;						// don't change this
	bzero(&lights[0].buf, sizeof(lights[0].buf));			// don't change this
	
	// SECOND SENSOR --> TSL2561_ADDR_FLOAT
	lights[1].adapter_nr=1;						// change this according to your i2c bus
	lights[1].sensor_addr=TSL2561_ADDR_FLOAT;			// don't change this
	lights[1].integration_time=TSL2561_INTEGRATIONTIME_402MS;	// don't change this
	lights[1].gain=TSL2561_GAIN_16X;				// don't change this
	lights[1].adapter_fd=-1;					// don't change this
	lights[1].lasterr=0;						// don't change this
	bzero(&lights[1].buf, sizeof(lights[1].buf));			// don't change this
	
	// THIRD SENSOR --> TSL2561_ADDR_HIGH
	lights[2].adapter_nr=1;						// change this according to your i2c bus
	lights[2].sensor_addr=TSL2561_ADDR_HIGH;			// don't change this
	lights[2].integration_time=TSL2561_INTEGRATIONTIME_402MS;	// don't change this
	lights[2].gain=TSL2561_GAIN_16X;				// don't change this
	lights[2].adapter_fd=-1;					// don't change this
	lights[2].lasterr=0;						// don't change this
	bzero(&lights[2].buf, sizeof(lights[2].buf));			// don't change this
	
	// initialize the sensors
	for(i=0; i<3; i++) {
		rc = TSL2561_OPEN(&lights[i]);
		if(rc != 0) {
			fprintf(stderr, "Error initializing TSL2561 sensor %i (%s). Check your i2c bus (es. i2cdetect)\n", i+1, strerror(lights[i].lasterr));
			return 1;
		}
		// set the gain to 1X (it can be TSL2561_GAIN_1X or TSL2561_GAIN_16X)
		// use 16X gain to get more precision in dark ambients, or enable auto gain below
		rc = TSL2561_SETGAIN(&lights[i], TSL2561_GAIN_1X);
		
		// set the integration time 
		// (TSL2561_INTEGRATIONTIME_402MS or TSL2561_INTEGRATIONTIME_101MS or TSL2561_INTEGRATIONTIME_13MS)
		// TSL2561_INTEGRATIONTIME_402MS is slower but more precise, TSL2561_INTEGRATIONTIME_13MS is very fast but not so precise
		rc = TSL2561_SETINTEGRATIONTIME(&lights[i], TSL2561_INTEGRATIONTIME_101MS);
	}
	
	// you can now sense each sensor when you like
	for(i=0; i<3; i++) {
		// sense the luminosity from the sensors (lux is the luminosity taken in "lux" measure units)
		// the last parameter can be 1 to enable library auto gain, or 0 to disable it
		rc = TSL2561_SENSELIGHT(&lights[i], &broadband, &ir, &lux, 1);
		printf("Test sensor %i. RC: %i(%s), broadband: %i, ir: %i, lux: %i\n", i+1, rc, strerror(lights[i].lasterr), broadband, ir, lux);
	}
	
	// when you have finisched, you can close things
	for(i=0; i<3; i++) {
		TSL2561_CLOSE(&lights[i]);
	}
	
	return 0;
}